Panzer4 Turret Roof Armor Thickness

Armor with two or more plates spaced a distance apart falls under the category of spaced armour spaced armour can be sloped or unsloped. Test of 26 66cm class a main armament turret face port plate originally for ijn shinano the third japanese yamato class super battleship converted into an aircraft carrier instead and sunk on its way to final fitting out yard by a u s. The maximum thickness holed at jutland was 9 inches.

orange acrylic sheet old style wooden screen doors osha standards for roof hatches owens corning roof shingles how to install painting cement fiberboard siding nuvo water filter price in bangladesh outdoor shade mesh 4 ft hang roof painting abitibi siding

Panzer Iv Ausf H Winter 43 44 In Ostland Russia Ausf H Version Indicated By Its Turret Schurzen It Had Hull Schurzen Pla Panzer Iv War Tank Tanks Military

Panzerkampfwagen Iv Discussion Page 3 Medium Vehicles War Thunder Official Forum

Pz Iv J War Thunder Wiki

German Panzer Iv Introduced 1939 75 Mm Cannon 2x 7 92 Mm Machine Guns 27 6 Tons Multiple Variants Were Produced Using Th Panzer Iv War Tank Tank

The Panzer Iv K And Its Proposed Impact On German Armor Armored Vehicle History World Of Tanks Official Forum

Creating A Wwii Germany Themed Imperial Guard Army Seeking Advice Not Politics Forum Dakkadakka Roll The Dice To See If I M Getting Drunk

D were produced with 50 mm.

Panzer4 turret roof armor thickness.

The upper superstructure frontal armor was 80 mm at a 50 angle the sides were 40 mm at a 19 angle the rear armor was 30 mm and the top was 20 mm. Increasing the turret front armour to about 10 inches would probably suffice. The engine compartment design and armor were unchanged with 20 mm all around and 10 mm of top armor. The last 68 ausf.

Preference given to data from jentz. 10 mm 0 39 in. Pig s head style mantlet. The commander s cupola had all around 14 5 mm of armor with the two hatch doors being 8 mm thick.

50 mm 2 0 in turret side and rear. The side armor was 30 mm the rear 20 mm and the bottom was 10 mm. G were produced without the added 30 mm. Spaced armor that is not sloped is generally designed to provide protection from explosive.

5 mm 0 20 in to 8 mm 0 31 in turret front. 10 mm 0 39 in schürzen. The thickness of the front plates on the turret and the weapon mantlet was 50 mm and this thickness was not increased in future upgrades. The front turret armor was 16 mm at a 10 angle while the sides and rear were 14 5 mm at 25 angle and the top was 10 mm at 83 90 angle.

The frontal turret armor plate thickness consisted of 120mm at 20 degrees 60mm on the sides and rear at 25 degrees 40mm flat on the roof and 150mm of cast armor on the saukopf english. Hull roof and floor. Improving the machines protective armor during production was a slow process and by november only about half of the tanks included the reinforced armor. The hull s armor was largely the same as the ausf g with the differences lying on the hull s roof.

Having more armour might help but adding proper safety features to cope with a catastrophic hit would probably be a better strategy. Submarine which made up far left side of turret face looking from inside turret out of gun port with d shaped cutout making up about half of. Armor on the lower hull front. 30 mm 1 2 in turret roof.

Depending on the source the front armor thickness of the turret varies between 15 to 20 mm. When sloped it reduces the penetrating power of bullets and solid shot as after penetrating each plate projectiles tend to tumble deflect deform or disintegrate. J were produced without face hardened armor and the superstructure roof was thickened to 16 mm.